~ Mimi's Adventures in Crafting ~

The musings and adventures of a "forty-something" wife and mother whose inner-artisan has been reignited. Enter my realm and enjoy....


Monday, November 16, 2009

M5142


PR: M5142

Pattern Description: Misses’ Classic Fit Jeans in two lengths with two waistband treatments

Fabric Used: Non-Stretch Cotton Denim, 12 oz.

Pattern Size: EE Cut a 20 but will need to cut smaller size next time

Did it look like the photo/drawing on the pattern envelope once you were done sewing with it? Yes but I did modify the design to fit my taste

Were the instructions easy to follow? Didn’t use them

What did you particularly like or dislike about the pattern? The pattern was easy to sew. Being a Palmer/Pletsch I figured that there would be at least an explanation of the flat back pleats in the instructions but there weren’t any. I didn’t need this information but for an inexperienced sewer who doesn’t understand fit they would require an explanation as to what to do with this fit technique.


Pattern alterations or any design changes you made: I participated in the Build A Better Jeans class and didn’t have the opportunity to buy the Jalie 2908 jean pattern that I had wanted to use for this project so had to resort to using this one being as it was readily available locally. I made several alterations to this pattern being as I didn’t like the final shape shown on the pattern envelope and technical drawings. I wanted the jeans to be more like my RTWs so I adjusted the side seam going from the hip area and tapering in at the knee by 1 ½ inches and then flaring back out at the hem. I also did the same for the inseam starting at the crotch tapering in 1 ½ inches at the knee and back out to the flared hem. I shortened the crotch front by 3/8 inch and lengthened the jeans 2 ½ inches. I added 3/8 inch to the waistband to bring it in line with the width of my RTWs. Due to the increased width in the waistband I added some length to the belt loop piece. I didn’t want my side front piece to be all denim so I changed the design cutting the piece from my lining fabric and making a denim piece to overlay half of the side front so that the lower part of the pocket was out of the lighter weight fabric and reducing some bulk in that area. I decreased the width of the ticket pocket and moved its position over a little bit towards the side seam. I moved the back pockets as well not liking where they were sitting on my form. They had them too close to the center back. As far as fitting goes, this pattern offers a generous 1 inch seam allowance but I found I needed to take an additional 1/2 inch to 1 inch more from the waist down to the knee. I did make up the pattern according to my hip size but still needed to make these additional adjustments. Being as these were my “mock-ups” I will have to redraw my pattern downsizing and adjusting it for the additional amount needed to be taken in. I also did the “Rocketboy Waistband” treatment on my jeans. An explanation of this can be found on PR under the Jeans Sew Along thread, page 31 as well as on my blog M5142: The Finishing Touches.


Would you sew it again? Would you recommend it to others? Yes but if you are looking for a tight fitting jean, this pattern isn’t it, you might want to consider the Jalie 2908 instead using stretch denim with lycra.

Conclusion: All in all I am satisfied with how my jeans turned out. I will be making another pair to try and improve the fit. I liked the fact the jeans were sewn from denim without lycra in it.

3 comments:

  1. They look very nice! I have the Jalie pattern and some denim, but I haven't had time to start on them yet. I figure jeans will take longer than most of the things I make!

    ReplyDelete
  2. O my, that is one great pair of jeans....You did a terrific job fitting the jeans...

    ReplyDelete
  3. it looks very good, the jeans. i make the pockets inside, also from that kind of crazy fabric.

    ReplyDelete

Related Posts with Thumbnails